Noise sensor

[roberbike]

Firmware for noise sensor slave by i2c.
Auto detect flash sice. Board need to has > 4 Mb of flah memory.
tested with :

S2 4Mb
S3 8Mb
T-display 4Mb
C3 4Mb
Log example:
==>[INFO] Time for initial setup over. Booting..

-->[INFO] ESP32MAC : CC:BA:97:15:55:32
-->[INFO] Hostname : CanAirIO532
-->[INFO] Revision : r990
-->[INFO] Firmware : 0.7.0
-->[INFO] Flavor : ESP32S3
-->[INFO] Target : dev
-->[INFO] == Detecting Sensors ==
-->[INFO] Sensorslib version : 0.7.6
-->[INFO] config UART sensor : GENERIC
-->[SLIB] temperature unit : C
-->[SLIB] temperature offset : 0.00
-->[SLIB] altitude offset : 0.00
-->[SLIB] sea level pressure : 1013.25 hPa
-->[SLIB] only i2c sensors : false
-->[SLIB] sensor registered : SPS30 :D
-->[SLIB] sensor registered : NOISE :D
-->[SLIB] sensors count : 2 (SPS30,NOISE,)
-->[INFO] restored saved unit : PM2.5
-->[SLIB] sensors units count : 10 (PM1,PM2.5,PM4,PM10,Noise,NoiseAvg,NoisePeak,NoiseMin,NoiseAvgLegal,NoiseAvgLegalMax,)
-->[WDOG] watchdog check each : 120 seconds.
-->[WIFI] device network IP : 192.168.68.109
-->[WIFI] publish interval : 10 sec.
-->[FOTA] remote OTA update : not need update
-->[IFDB] influxdb.canair.io : connected!
-->[INFO] InfluxDb cloud : enabled
-->[INFO] WiFi current config : enabled
-->[INFO] CanAirIO station name : EZTESP32S355532
-->[BTLE] Bluetooth GATT : ready for config client!
-->[INFO] Wifi connected to : MiDeco
-->[INFO] sensors units count : 10
-->[INFO] show unit selected : PM2.5
-->[HEAP] sizeof sensors : 01176b
-->[HEAP] sizeof GUI : 00108b
-->[HEAP] free memory : 144076b

==>[INFO] Setup end. CLI enable. Press ENTER ===
CanAirIO:$ -->[SLIB] SPS30 read : done!
-->[SLIB] sensors values : PM1:4.0 PM2.5:4.0 PM4:5.0 PM10:5.0 Noise:33.0 NoiseAvg:32.0 NoisePeak:36.0 NoiseMin:32.0 NoiseAvgLegal:32.0 NoiseAvgLegalMax:32.0
-->[SLIB] sensors count : 2 (SPS30,NOISE,)
-->[SLIB] sensors units count : 10 (PM1,PM2.5,PM4,PM10,Noise,NoiseAvg,NoisePeak,NoiseMin,NoiseAvgLegal,NoiseAvgLegalMax,)
-->[WIFI] AP RSSI signal : -80 dBm
-->[HEAP] LOOP bytes used : 00000b/133Kb
-->[SLIB] SPS30 read : done!
-->[SLIB] sensors values : PM1:4.0 PM2.5:4.0 PM4:5.0 PM10:5.0 Noise:32.0 NoiseAvg:32.0 NoisePeak:36.0 NoiseMin:31.0 NoiseAvgLegal:32.0 NoiseAvgLegalMax:32.0
-->[SLIB] sensors count : 2 (SPS30,NOISE,)
-->[SLIB] sensors units count : 10 (PM1,PM2.5,PM4,PM10,Noise,NoiseAvg,NoisePeak,NoiseMin,NoiseAvgLegal,NoiseAvgLegalMax,)
-->[WIFI] AP RSSI signal : -79 dBm
-->[HEAP] LOOP bytes used : 00000b/133Kb
-->[BATT] avarage: 0.0000 slope : 0.000000
-->[BATT] is discharging : True
-->[SLIB] SPS30 read : done!
-->[SLIB] sensors values : PM1:4.0 PM2.5:4.0 PM4:5.0 PM10:5.0 Noise:34.0 NoiseAvg:32.0 NoisePeak:36.0 NoiseMin:31.0 NoiseAvgLegal:32.0 NoiseAvgLegalMax:32.0
-->[SLIB] sensors count : 2 (SPS30,NOISE,)
-->[SLIB] sensors units count : 10 (PM1,PM2.5,PM4,PM10,Noise,NoiseAvg,NoisePeak,NoiseMin,NoiseAvgLegal,NoiseAvgLegalMax,)
-->[WIFI] AP RSSI signal : -80 dBm
-->[HEAP] LOOP bytes used : 00000b/133Kb
-->[SLIB] SPS30 read : done!
-->[SLIB] sensors values : PM1:4.0 PM2.5:4.0 PM4:5.0 PM10:5.0 Noise:33.0 NoiseAvg:32.0 NoisePeak:42.0 NoiseMin:31.0 NoiseAvgLegal:32.0 NoiseAvgLegalMax:32.0
-->[SLIB] sensors count : 2 (SPS30,NOISE,)
-->[SLIB] sensors units count : 10 (PM1,PM2.5,PM4,PM10,Noise,NoiseAvg,NoisePeak,NoiseMin,NoiseAvgLegal,NoiseAvgLegalMax,)
-->[WIFI] AP RSSI signal : -80 dBm
-->[HEAP] LOOP bytes used : 00000b/133Kb
-->[BATT] avarage: 0.0000 slope : 0.000000
-->[BATT] is discharging : True